下载
Industrial Current/Voltage Output Driver
with Programmable Ranges
Data Sheet
AD5750/AD5750-1/AD5750-2
Rev. F Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2014 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
FEATURES
Current output ranges: 4 mA to 20 mA, 0 mA to 20 mA, 0 mA
to 24 mA, ±20 mA, and ±24 mA
±0.03% full-scale range (FSR) total unadjusted error (TUE)
±5 ppm/°C typical output drift
Voltage output ranges: 0 V to 5 V, 0 V to 10 V, ±5 V, and ±10 V
with 20% overrange
±0.02% FSR TUE
±3 ppm/°C typical output drift
Flexible serial digital interface
On-chip output fault detection
Packet error checking (PEC)
Asynchronous CLEAR function
Flexible power-up condition to 0 V or tristate
Power supply range
AV
DD
: +12 V (± 10%) to +24 V (± 10%)
AV
SS
: −12 V (± 10%) to −24 V (± 10%)
Output loop compliance to AV
DD
− 2.75 V
Temperature range: −40°C to +105°C
32-lead, 5 mm × 5 mm LFCSP package
APPLICATIONS
Process controls
Actuator controls
PLCs
GENERAL DESCRIPTION
The AD5750/AD5750-1/AD5750-2 are single-channel, low cost,
precision voltage/current output drivers with hardware- or
software-programmable output ranges. The software ranges are
configured via an SPI-/MICROWIRE™-compatible serial interface.
The AD5750/AD5750-1/AD5750-2 target applications in PLC
and industrial process control. The analog input to the AD5750/
AD5750-1/AD5750-2 is provided from a low voltage, single-supply
digital-to-analog converter (DAC) and is internally conditioned
to provide the desired output current/voltage range. Analog input
ranges available are 0 V to 2.5 V (AD5750-1/AD5750-2) or 0 V
to 4.096 V (AD5750).
The output current range is programmable across five current
ranges: 4 mA to 20 mA, 0 mA to 20 mA, 0 mA to 24 mA, ±20 mA,
and ±24 mA. An overrange of 2% is available on the unipolar
current ranges.
Voltage output is provided from a separate pin that can be
configured to provide 0 V to 5 V, 0 V to 10 V, ±5 V, or ±10 V
output ranges. An overrange of 20% is available on the voltage
ranges.
Analog outputs are short-circuit and open-circuit protected and
can drive capacitive loads of 1 µF and inductive loads of 0.1 H.
The devices are specified to operate with a power supply range
from ±12 V to ±24 V. Output loop compliance is 0 V to AV
DD
−
2.75 V.
The flexible serial interface is SPI and MICROWIRE compatible
and can operate in 3-wire mode to minimize the digital isolation
required in isolated applications. The interface also features an
optional PEC feature using CRC-8 error checking, useful in
industrial environments where data communication corruption
can occur.
The devices also include a power-on-reset function, ensuring that
the devices power up in a known state (0 V or tristate), and an
asynchronous CLEAR pin that sets the outputs to a zero scale/mid-
scale voltage output or the low end of the selected current range.
The HW SELECT pin is used to configure the parts for hardware
or software mode on power-up.
Table 1. Related Devices
Part Number Description
AD5422
Single channel, 16-bit, serial input current
source and voltage output DAC
AD5751
Industrial I/V output driver, single supply, 55 V
maximum supply, programmable ranges
AD5420
Single channel, 16-bit, serial input, 4 mA to
20 mA current source DAC
页面指南
